How To Tape For Painting

Do I Need To Tape Before I Paint

How To Use Painter’s Tape – Ace Hardware

Painting a room is the best way to update its personality and aesthetics. But before picking up a brush or roller, you need to prepare the space. Apart from moving furniture, laying down drop cloths, and cleaning baseboards, many DIY painters often neglect an important step taping.

As a rule of thumb, professional painters advise applying painters tape. It helps to assure clean lines with no messy edges making your painting project look more professional. But some DIY painters believe that taping takes too much time and is unnecessary. Well take a look at some of the reasons why you should use tape before painting, and some tricks of the trade to make the job faster.

Use Tape When Covering Your Floors

Placing tarps on the floor will go a long way in protecting your hardwood or carpets from paint spills. But be aware that tarps will shift a lot during this process, and it can be difficult to keep them flush against your baseboard. Its a good idea to purchase some kraft paper rolls for some added protection. Use masking tape to adhere them to the floor, right up against the baseboard. This way, when your tarps move an inch or two, your floors are still protected.

How To Apply Painters Tape To Trim And Baseboards

  • Pull tape about 6″ off roll
  • Place on trim board
  • Use a putty knife to apply pressure
  • Repeat the process

When applying painters tape to baseboard trim, it will seal best when a flexible putty knife is used to apply pressure as you lay your tape line. Start by laying about 6″ of tape against your surface, then unroll about 6″ more. Laying small sections of tape at a time will help to keep your tape as straight as possible.

Also Check: How To Make Oil Paint

When To Remove The Painters Tape

Wait until the painted surface is completely dry before removing the tape, usually 24 to 48 hours. The last thing you want to happen after spending all that time prepping and painting are for a drip of paint to ruin your entire project. Remove the tape by carefully lifting and peeling back the tape on an angle. The result will be a professional-looking paint project with clean, straight lines.

Franklin Painting crews can meet your painting needs! Offering exterior house painting, interior painting, deck staining, and more. Our professional house painters can do the job! Our highly trained, professional and courteous employees make sure the job gets done the way you deserve.

How Do I Remove It

Tips for How to Use Painters Tape

The most important thing to know about removing tape is when to do it. It’s best to wait until the paint is completely drythat way, you avoid any late-in-the-game drips from still-wet walls AND avoid the possibility of smudging unpainted surfaces with wet paint stuck to the tape. For extra precision , use a knife to gently score the edge of the tape to ensure a clean peel.

Also Check: Paint Bubbling On Wall Water Damage

Tear Your Tape When You Find Difficult Spots

Applying the tape the usual way can be challenging with smaller items , narrow curves or crooked spots.

Small pieces of tape work best around uneven decorative moulding and curved edges.

Ok, this may sound like a really long and boring job, but think about it: your only alternative is to do an uneven job and retouch with a tiny brush all the mistakes you made for being lazy. What about now?

Masking Tape Painting Techniques

Here are 6 masking tape tips that will help you get a flawless paint job done, quickly and with no mess:

1. Always start with a clean surface. Remove dust and dirt from edges and surfaces before applying, to guarantee perfect adhesion and crisp edges. Microfiber cloths are preferable, but if you use wet cloths be sure that the surface has dried before starting with the application.

2. When applying the tape, use short strips. They are easier to apply and dont get tangled. They’re also preferred when painting irregular surfaces and edges because it’s easier to apply the tape and obtain crisp lines.

3. After applying, make sure to seal the edges running your fingers back and forth over them. Check the presence of air bubbles and lifted edges in the marking tape because the paint might seep through them.

4. Overlap the strips edges for easy removal. It will be easier to find them and won’t cause any damage to the paint. And when removing the tape, start pulling at the opposite side of where you applied it.

5. Brush a little bit of paint of the same color as the surface along the tapes edge to create an additional seal against paint bleeding under the tape. It also guarantees higher precision when painting the surface where the masking tape was applied.

6. Finally, when the paint is dry to the touch, remove the tape pulling slowly at a 45-degree angle. Be gentle to avoid the paint getting damaged and the masking tape breaking.

Also Check: Best Paint For An Exterior Door

How To Paint In A Room With Carpet

  • Cut 3″ strips of masking paper
  • Apply painters tape to trim leaving an overhang
  • Stick 3″ masking paper to painters tape creating a flap
  • Lay down a plastic or canvas drop cloth on entire carpet

Masking paper is a great tool to keep paint off of carpet or other flooring. First, you’ll apply painters tape using the tricks listed above. Then, you’ll add about 3″ of masking paper to the painters tape. This will create a flap that will catch most paint drips from brushes and rollers. Any flap wider than 3″ will most likely sag, which will not catch your paint or protect your floor.

Drop clothes can also be laid out to protect the entire room. For painting best practices, cover the entire floor with a plastic sheeting, and then top that with a canvas top. The canvas is more durable to withstand foot traffic while painting, and it will absorb paint splatter better.

How Do You Keep Paint From Bleeding Under Tape

How To Use Painter’s Tape – Ace Hardware

If you want to create a seal between the tape and the base coat, apply a very thin coat of paint over the edges of the tape. If you want your next paint color to not bleed through, you need to seal the edge of the tape.

If you want to seal the entire tape, you can use the same technique, but you will need to paint over all the areas that you dont want the paint to seep into. Apply a second coat to the top and sides of your tape. This is the final step, and its the most time-consuming part of this process.

To do this, use a small paint brush to apply a thin, even coat over your first coat, then repeat the process for the second and third coats. Dont worry if you get a little bit of excess paint on the brush, it will come off in the next step. Once youre done, let it dry for a few minutes and then apply your final topcoat.

You May Like: How Many Paintings Did Van Gogh Sell

Invest In The Right Brush

Purchase a good brush with the money youre saving on tape. Rosss go-to is Wooster, specifically the Alpha. For the careful work needed when youre cutting inwhich is the process of painting the section nearest the ceiling or trim or wherever your stopping point ishe recommends a 2 1/2-inch angled brush. And for getting into a super tight spot, like a weird triangle along a stairway or that half inch between the door casing and the corner, we bust out an artists brush if we have to, he says.

Tape Walls Adjacent To Ceiling

If you plan to paint the ceiling, you may choose to tape the walls. This prevents the ceiling paint from contacting the walls. The tape applicator works well for these long runs.

  • Move the ladder to a corner of the room. Start the tape near the corner.
  • Run the tape the length of the wall, frequently moving the ladder.
  • Press newly applied tape with a finger to secure it to the wall.
  • When you reach a corner, cut off the tape, leaving 2 or 3 inches of extra tape.
  • Press that extra tape tightly into and around the corner.
  • Start a new piece of tape and continue the next wall run.
  • Once the walls are taped, paint the ceiling. After a maximum of two coats of ceiling paint, remove the tape.

    Recommended Reading: Paint Color Ideas For Bedroom

    Prepare The Work Area

    Before starting any paint project, remove furniture from the room in which you’re working, or place it in the center of the room and cover it with drop cloths. Place drop cloths or tarps on the floor and remove fixtures, window coverings, switch plates and outlet covers. You will want to cover the outside edge of anything you couldn’t remove with painter’s tape. See Step 3.

    Outside, use drop cloths to cover cars, patio furniture, shrubs and anything else you don’t want splattered. Remove all screens, light fixtures, plumbing outlets, electrical covers, shutters and address numbers/placards. Again, you will want to cover the edges of anything you couldn’t remove with painter’s tape.

    Properly cleaning surfaces is necessary for both painter’s tape and paint adhesion. Painter’s tape won’t adhere well to dirty or damaged areas and poor adhesion can lead to paint infiltrating under the tape. Use a sponge to wipe down all surfaces with mild detergent and water, and allow it to dry.

    Make Painting Easier With Painters Tape

    Tips for How to Use Painter

    When you are using tape for clean, neat painting, take your time and use utility tools as needed. When you take the time to apply painters tape carefully, youll make your painting job easier. It will also look professional. Painters tape comes in different varieties, which will allow you to get the right product for the job. Painters tape is available from True Value. Check here to locate a store near you.

    Also Check: Benjamin Moore White Ceiling Paint

    Don’t Miss: What Paint Brands Does Lowes Carry

    Why You Should Tape Before Painting

    Painters tape is an inexpensive item that is widely available in any hardware or craft store. It helps avoid painting mistakes and makes your project more productive. Pros also use painters tape to ensure straight lines, prevent overlaps and avoid getting paint on other surfaces like the molding or ceiling.

    The tape is applied to surface areas that you dont want to paint or will use another paint color. For instance, applying tape to the molding will allow you to paint a wall faster ensuring you can paint all the way down to the edge of the molding without getting paint on the molding itself. Also, the painters tape is designed to adhere to the surface without leaving marks or residue.

    Other types of tape, like masking tape, for example, will not adhere to all surfaces, and some kinds of tape can leave glue marks on the surface.

    Painters tape can be applied to practically any surface like windows, ceilings, walls, and wood furniture. It is easily removed without splintering, so you dont have pieces of tape stuck to the surface. It also wont peel off while youre painting. The tape can also help in creating colorful shapes and intricate designs and patterns.

    What Kind Of Tape Do You Use On Windows

    Window tape is a type of adhesive that you use to seal the edges of your windows. There are different types, and each has its own benefits and drawbacks.

    Some tapes are stronger than others, but all have one thing in common: they stick to glass

    • 3M Transparent Weather Sealing Tape is a great way to keep cold air out and seal cracks in your windows. The tape is flexible and easily conforms to angles and curves, making it easy to install. It also removes without leaving any residue, so you can reuse the tape multiple times without issue.
    • This kind of tape is often used on window frames to prevent drafts and moisture infiltration from the outside world into the building. Its also commonly used for sealing around door seals and gaps between walls and ceilings insulation .
    • The weather sealing properties of this type of tape make it an excellent option for use on glass surfaces that are vulnerable to scratches or rain damage .
    • If you have trouble removing old tapes from your windows, try using a solvent like acetone before pulling them off by hand .
    • Be sure to read the product label carefully before buying this type of tape some tapes may not be safe for certain types of glass or plastic.

    Read Also: Colors To Paint Inside House

    How To Protect Walls When Painting A Ceiling

    If youre painting a ceiling, draping lightweight plastic sheeting is the best way to protect your walls.

    Heres a quick and easy way to hang the plastic. Use 1-1/2 in.-wide painters tape with medium to high holding strength. Press the top edge down, but leave the bottom loose. It should curl up slightly to expose the sticky underside. Stick the edge of the lightweight plastic sheeting to the tape and let it hang to the floor. You dont need to tuck the plastic underneath the tape. Just curl the tape back onto itself and stick the plastic to the exposed adhesive.

    Always test first in an inconspicuous area to make sure the tape doesnt pull paint from the wall. Super-thin painters plastic sheeting is a good choice for this type of taping because its inexpensive and lightweight, and it produces less waste. Overlap the plastic at doorways to create an opening.

    Are Rounded Corners In Style 2021

    How To Apply Masking Tape or Painters Tape

    Rounded corners are more appealing and friendlier than ever before, and professional designers are getting requests for rounded edges in more places than ever before. Its a trend thats been around for a while, but its really taken off over the last few years. Its something that weve been seeing more and more of in our stores, and it seems to be catching on in other places as well.

    You May Like: How To Prep Concrete For Paint

    How Do I Install Archway Corner Bead

    Run another screw through the corner bead and into the wallboard. Using a 1-1/4-in. x 6-ft. piece of 2×4, drill a pilot hole in the center of each corner. Drill two pilot holes at the top and bottom corners. Then, using a 3/8- in.-dia. hole saw, cut the corners to size. You may need to use a drill press to make the cuts.

    If you dont have one, you can use an electric drill to drill the holes, but be careful not to over-drill or youll have to re-do the entire job. Once youve cut your corners, sand the edges smooth with 220-grit sandpaper and then apply a coat of polyurethane varnish.

    Paint Over The Edges Of The Tape

    Once you have finished painting, you may notice that paint has seeped under the tape in some areas. To fix this, run a small paintbrush along the edge of the tape. This will help to seal any gaps and prevent paint from bleeding through.

    If the paint has already dried, you can use a sharp utility knife to scrape away the excess carefully. Be sure to go slowly and be careful not to damage the surface beneath. Once you have removed the excess paint, you can touch up the area with a fresh coat of paint.

    You may also want to sand down the edges of the tape to create a clean, straight line. Again, this is an optional step but can be helpful if you are looking for a flawless finish.

    Read Also: How Much Does It Cost To Paint Exterior Of House

    Step : Apply The Tape To The Trim And Ceiling

    The next step is identifying the areas you need to protect. In most rooms, this means the ceiling, the trim around windows and doorways, and baseboards.

    Rip off 1-foot-long pieces of tape, which are easier to handle. Apply them to the intended area in a straight line. Start in the middle of each piece, smoothing it down with a finger or putty knife as you go. If any pieces bubble or lay unevenly, its best to remove them and try again.

    Step : Remove The Tape As Soon As Youre Done Painting

    Tips for How to Use Painters Tape

    While painters tape can usually remain in place for hoursor even dayswithout causing any damage to the surface underneath, its best to remove it as soon as possible to ensure the best results.

    Slowly peel the tape off the trim at a 45-degree angle. If any sections dont come off easily, a putty knife usually helps.

    Also Check: Hand Painted Portraits From Photos

    Painter’s Tape Vs Masking Tape: What’s The Difference

    Go to any hardware store and ask where to find the tape, and you’re sure to be met with a question about which type you want: duct, masking, adhesive, cellophane, electrical, painter’s, double-sided, plumber’s, etc. Most of those tapes look and feel so different that it’s easy to decide which one is right for the job. After all, wrapping the kids’ birthday presents in black electrical tape is definitely gonna draw some looks. But for two of the most commonly used tapes masking and painter’s the differences aren’t as obvious.

    Aside from the painter’s tape name easily giving away its specialty, both masking tape and painter’s tape are made with a crepe paper backing, have similar weights and, in a pinch, can be used for the same jobs. In fact, they’re technically from the same family all painter’s tapes are masking tapes. But on the flip side, not all masking tapes are painter’s tapes.

    So, if they are really that similar, is it truly necessary to choose one over the other? The answer will depend on your project type, your budget and your time.

    Subscribe

    Related articles