Do I Need To Prime Concrete Before Painting
It is prudent to apply a primer to the concrete before painting. However, ensure that you apply the formula after removing all dirt and efflorescence from the surface. A primer accomplishes the following essential functions.
- It soaks into the concrete and protects it from overtime damage.
- The formula turns an uncooperative surface for paint into one that perfectly receives paint and top coasts beautifully.
- You will also enjoy using a stain or paint coat for an extended duration.
- The product fills voids and small gaps to deliver a uniform and smooth surface.
- It functions as a bonding agent between the paint and concrete. Thus, it assures excellent adhesion to both surfaces.
Even so, sometimes, you may not need a primer if you have an existing surface. But, you need to prim if the concrete is peeling, chalking, unpainted, chipping, or is incompatible with the paint type suitable for the job.
On top of that, primers have special attributes that reduce the number of bubbles or pinholes caused by trapped hair. Therefore, they reduce water loss and improve topcoat adhesion significantly.
It would help to know the various primers we have in the market. They come in three forms: acrylic or latex, alkyd or oil-based, and tinted shellac. The formulas are suitable for both interior and exterior applications. Therefore, you will always get a suitable one for your paint job.
Also, check out the primers below and how they work.
Masonry Concrete Cement Block
-
All new surfaces must be cured according to the supplier’s recommendations- usually about 30 days.
-
Remove all form release and curing agents.
-
Rough surfaces can be filled to provide a smooth surface.
-
If painting cannot wait 30 days, allow the surface to cure 7 days and prime the surface with masonry primer.
How Long Do You Have To Wait To Paint A House After Pressure Washing
Moisture within the siding following power washing In a perfect world, you should wait about three to four days afterward before you start exterior painting. This gives typical surfaces like wood, brick, and other porous materials time to fully dry. It’s never a good idea to paint onto still wet surfaces.
Read Also: How Much Does It Cost To Paint Kitchen Cabinets Professionally
Top 5 Interior Paints From Cr’s Tests
These standout formulas, listed in alphabetical order, are recommended for your next paint project. Youll notice a couple of them have Greenguard Gold certification, meaning they emit lower levels of volatile organic compounds, or VOCsparticularly formaldehydethan the industry standard. VOCs are chemicals that can easily become airborne and affect your health, according to the Environmental Protection Agency. Low levels of VOCssome paints even come with a zero VOCs claimare ideal for interior paint projects.
Surface Prep For Painting: Remove Cracked Or Peeling Paint

Begin surface prep for painting by removing any loose, peeling paint with a paint scraper and sandpaper. Sand all edges to smooth the surface and help the new paint adhere. Scrub all surfaces with a mild detergent and a sponge or rag to remove all dirt, grease, oil, etc. Rinse surface well and allow to dry. Spot-priming will help the new paint adhere and give a better finished look.
Don’t Miss: Black And White Tree Painting
Tape Along Skirting Boards Window & Door Frames
This helps ensure a neat and professional finish. Masking tape peels too easily and can make your job more difficult, so invest in good quality to keep the paintwork tidy.
Now youre ready to paint! Set up a work area in an accessible part of the room , where you can pour and clean as necessary. This will save you time clearing up and help keep your workspace organised and efficient. Happy painting!
Step Two: Prep The Space
Place a drop cloth on the floor to protect it, and use painters tape to cover any areas that you dont want to paint.
Next, you want to remove all of the hardware from your cabinet.
Once all of the hardware is removed, its time to clean and sand your cabinet doors and drawers. I chose to leave my doors on the hinges and drawers in the cabinets for this part, but you can also remove them for this step if you desire.
It is VERY IMPORTANT to make sure your cabinets are clean before painting, especially in a bathroom. Bathroom cabinets can have lots of build up from hairspray and other products we use in the bathroom. So you want to use a heavy duty cleaner that can cut through all the grit and grim. I used Goof Off, but you can also use a TSP cleaner, just be sure to wear gloves and eye protection.
If you do not clean the cabinets well, the paint will not adhere properly.
After you have throughly cleaned all the drawers, cabinet doors, and cabinet base, its time to sand. You want to use a 180 or 220 grit sanding sponge to lightly sand all surface areas that you will be painting.
When you are finished sanding, go over all of the areas with a tack cloth to get rid of sanding dust.
Once everything is properly prepped to paint, its time to set up your painting station. Its best for it to be in a place that is well-ventilated and where you have plenty of space.
Also Check: Best Sherwin Williams Paint For Cabinets
How To Prepare Walls After Removing Wallpaper
- Working on a previously wallpapered surface? Peel-able wallpaper is easy to get rid off , but wallpaper hung with paste can be slightly trickier to remove. Take it off carefully using a stripping knife, taking extra care not to damage the plaster behind.
- If a few scraps of wallpaper are holding on for dear life, soak with a sponge and hot water to soften before stripping. Finish off by sanding lightly with a fresh piece of sandpaper.
Read our article on how to paint over wallpaper for more information.
How Soon Can You Paint After Etching Concrete
The general rule is to follow the manufacturers guidelines because some etching products need a neutralizing component. But, you will always be on the safe side if you allow a minimum of four days before foot traffic and ten more days before vehicle traffic or other paint applications.
In addition, temperature and humidity levels shorten or lengthen the waiting duration. Therefore, choose a good time to handle the project. Besides that, etching materials have sandquantities that influence the formulas working speed. They only need approximately 15 to 30 minutes to work their way through the initial layer.
Recommended Reading: How To Paint With Acrylic
Don’t Forget The Painter’s Tape
Unless you’re a pro at cutting in, painter’s tape is your best friend. Use it to tape off the trim, molding, floor, and other surfaces you don’t want painted. Bonus: The work goes faster when you don’t have to worry about painting a perfect line.
It’s best to remove the tape while the paint is slightly tacky. This way, you avoid ripping off dried paint later.
Get Creative And Turn Plain Clay Pots Into A Colorful Accent For Your Home
- Pin
If you’re looking for a fun, easy DIY project that you can complete in an afternoon, look no further. Painting terra-cotta pots is a great way to turn a plain planter into a colorful accent for your home or yard. It’s also a good way to give your plants and herbs a pretty new home or create a thoughtful handmade gift for a friend. Our step-by-step tutorial will teach you how to make a cool dipped effect for a modern look, but the sky’s the limit when it comes to your flowerpot design. Terra-cotta pots are inexpensive and readily available in most garden centers and home supplies stores and you can find the rest of the supplies needed in your local craft store. Now grab your paintbrush and get started!
Recommended Reading: Can You Paint Roof Tiles
How Do You Paint Over Old Concrete
Proper preparation is mandatory as it helps to deliver a perfect and long-lasting finish. Hence, begin by evaluating the surface for curing compounds. Buff the surface thoroughly to reveal small spots beneath the old paint. Then, mix hydrated lime and denatured alcohol in equal proportions and apply the paste to the identified spots.
Allow the paste to dry until it becomes a thin crust. Next, use a bristled brush to scrape away the dried spots and sweep away the chips.
Check out the following project summary.
- Fill any scratches, holes, or gouges on the surface using a patching compound.
- Clean the concrete with warm water and trisodium phosphate and let it dry.
- Apply porch-and-floor enamel or paint. Begin with the perimeter, then move towards the middle.
- Scrap aways bumps and lumps on the surface. Then, sand regions where the paint did not adhere.
- Apply the second paint coat and let it cure.
Do A Thorough Visual Inspection And Prep

Any cracked, flaking or peeling areas need to be lightly sanded or scraped before applying new primer and paint because the weight of the new coat will pull the old paint loose. “You’ll just end up wasting your time and money if you don’t tackle that first,” says Tom Lee, Senior VP of Consumer Marketing for Behr. Greasy spots may also need a bit of washing with soap, followed by a rinse with clean water. Otherwise, wipe down with a damp cloth so that paint will have a clean, dust-free surface to stick to.
A well-placed piece of art may be the quickest way to disguise a hole in drywall, but for a professional fix, follow our tips for a smooth, finished surface.
Recommended Reading: What’s The Best Exterior Paint
How To Prep Cabinets Before Painting
September 4, 2021
If youre like most homeowners, your kitchen cabinets are maybe the most used item in your home! With all that wear and tear, its no wonder your kitchen cabinets are looking pretty worn out. But, before you even think about painting themdrop that paintbrush! First, youve got to learn how to prep your cabinets before painting.
I know, I know. Youve probably read some blog post about some miraculous painting solution where the blogger painted all her cabinets in under an hour without any prep work whatsoever.
WellI call BS on that.
Its not that the blogger is lying, but there are certainly some things she isnt telling you. Or perhaps she isnt expecting her cabinets to withstand actually being usedbecause after painting hundreds of cabinets, I can promise you this: prep work is ABSOLUTELY necessary if you want your paint project to last, and do the job its meant to do.
In fact, Id say its the most important part of the entire process!!!
By the way, if youre curiouscheck out this post on how do painted cabinets hold up over time. Ill keep it real with you all!
House Painting Photo : Paint The Trim
Protect the trim with two coats of quality latex paint. Apply paint to the underside of the trim the same way you applied the primer.
If the lower ends of your garage door trim just wont hold paint, heres why: Concrete soaks up water, then releases moisture slowly. So any wood next to ground level concrete stays damp, and that constant dampness breaks the wood/paint bond. The same goes for any wood that touches a deck, patio or other surface where water sits.
To correct the problem, create a gap between wood and horizontal surfaces. Then apply paintable water repellent to the bottom 16 in. of the wood. Properly applied repellents add several years to a paint job in areas highly vulnerable to moisture.
Begin by scraping away all the paint in the peeling area. Two or three coats of paint can usually be removed with a combination of paint scrapers and sandpaper . For heavier buildup, use a heat gun to soften the paint as you scrape. Be careful with a heat gunit can melt nearby vinyl and weather-stripping.
Next, undercut the trim to create a gap . When youre done, scrape any dirt or gunk out of the gap with a putty knife and blow out the dust using a vacuum or air compressor. To avoid staining the concrete, run at least three layers of masking tape under the wood. Apply repellent to all bare wood including the underside . Bend a putty knife in a vise to make a handy tool for reaching into tight areas. Remove the tape right after application.
Also Check: Paint Horses For Sale In Texas
Ugl Drylok Masonry Waterproof
UGL DRYLOKis a unique formula that keeps water out of the concrete. It also delivers stain resistance qualities and is thus perfect for areas with a lot of moisture.
You will get the product in white, blue, beige, and gray. On top of that, it offers essential qualities such as a non-slip finish, no primer needed, and hot tire pick-up resistance. Therefore, it is perfect for your driveway or garage.
The formula is fast drying and easy to clean with soap and water. Also, you will enjoy a shorter drying time and complete the paint job in record time.
Preparation: How To Prep The Surface
Before painting a ceiling, its important to take the time to prep the surface. This will help ensure that the paint goes on evenly and smoothly. Here are some tips for prepping a ceiling:
You May Like: Magnum Project Painter Plus True Airless
Why Paint Your Ceiling
Most people only think about painting their walls when theyre redecorating, but dont forget about the ceiling! A fresh coat of paint can really brighten up a room and make it feel new again. Here are a few reasons why you should consider painting your ceiling:
If you have a small room that you want to make look bigger, painting the ceiling white will help create the illusion of more space. The quality of the paint will also help bounce light around the room, making it feel brighter and airier.
If your ceilings are damaged or have cracks, painting them is a great way to cover up those imperfections and give your ceilings a smooth, finished look.
Here are a few tips to help you get started:
Different Types Of Primer
The three most common types of primer are latex, oil-based, and shellac. For the purposes of painting drywall, we recommend latex primers. It offers the best adhesion to the paints out of all the primers.
Like I mentioned earlier, just make sure that youre buying primer thats specifically designated for bare drywall. Its built specifically to help the drywall adhere better to paint, as opposed to other primers which are built for painting above other layers of latex or oil based paint.
You May Like: How To Touch Up Car Paint Chips
What Is The Best Way To Paint A Concrete Floor
Ensure that you are working on a clean and dry floor. Use a degreasing compound and rinse several times until the concrete is clean. Then, allow the floor to dry after applying every coat. Also, determine the source of the problem if the surface shows any signs of water seepage.
Next, follow the following simple steps to complete the job.
- Sand off and remove any old paint or ununiform regions. Then, vacuum the surface and wipe with a tack cloth.
- Use mix concrete patch compound to fill up any cracks or holes in the concrete. Use a trowel to push it in the depressions and let it dry thoroughly. However, you can skip this stage if the surface is smooth.
- Apply two coats of primer using a paint roller. Also, remember to let the surface dry properly between the coats.
- Use a clean paint compressor or roller to apply a minimum of two epoxy paint coats.
- Then, get a compressor or clean roller and apply several coats of a masonry sealer compound. Also, ensure that the surface dries between coats.
Can You Use Sugar Soap On Exterior Walls

Temporarily remove pot plants, garden hoses and any other items in close proximity to exterior walls. Wash walls with Sugar Soap and a sponge to get rid of any dirt or grime. Then hose down and allow time to dry. This will ensure the paint will adhere to the wall and not the dirt or grime.
How Do I Apply New Paint Over Old Paint?
More items
Don’t Miss: How To Remove Light Scratches From Car Paint